Відео

Jayden, confirming this router does has both bridge mode and wireless bridge mode under WAN setup.

@@cfldriven does wireless bridge mode allow you to put the router in any room

The water softener won't do much for the rust as it not a filter. Depending on the amount and size of the rust I would be concerned with it interfering or clogging the water line in the fridge. You can add a filter onto your water softener and bypass the fridge filter or use one on the fridge. I think whole house filter might be cheaper in long run.

Dan, what an important story to share. I sort recall something about liquid being able to get under the panel, but never imagine it would short out the control box. Makes you wonder way they didn't install a gasket to prevent this. You got me thinking maybe there is a way to apply some silicone along the cook top to control panel and rear vent. Have to do further research to make sure it doesn't cause more problems than it solves. Will you replace with another induction and does homeowner insurance cover any of it? Thanks for sharing.

Thank you for taking the time to watch and write in, much appreciated.

Adam, thank you for watching and sharing your setup. Always good to learn others approach.

Nancy, thank you for the suggestion. We will add it to our list. Thanks for watching.

Todd, did you call Cyberpower as they come with 3yr warranty. I had a battery die and they replaced the entire unit. Best of luck.

Mario, happy to hear this video helped you fix your machine. Congrats on completing the project.

Kim, it that case you may want to get a filter bypass cartridge or bypass plug for your Samsung. Thank you for sharing and watching.

Good to hear this video got your garage door on the right track! Thanks for watching.

You are correct the lifetime guarantee is a nice peace of mind. Thanks for the view.

I am still on the 2014 OEM battery and I have discovered as long as the voltage does not drop below 10.0V the car will turn on.

I would try going to MY FILES app and under Categories select Audio Files. If it has not been deleted all the audio files should be here. Best of luck and thanks for watching.

Your right about Sony not wanting to make this too good when they have higher end camera to sell. Thanks for sharing your story.

I use Adobe Premiere, but it is complex and expensive program. Windows PC and Mac computers usually have a more basic editing programs that are free and great for beginners.

In the USA visit www.sony.com/electronics/support/memory-camcorders-fdr-ax-series/fdr-ax53/downloads

John, great to hear the video was helpful. Thanks for watching and taking the time to write.

Congrats on planning ahead and replacing the rollers and pulley. Thank you for watching.

Leona, unfortunately in the USA you can not record programs with this TV as you can in other countries. However you can use a DVR like the Tablo TV ua-cam.com/video/bJgAgu1-46o/v-deo.html. Thank you for watching and writing in.

As you saw in the video the my transition from CH Stream+ was a bit shaky. After the tech support reset and firmware update the Tablo has reliable. I live in a poor reception area so along with high gain antennas, antenna pre-amp, I also run the Tablo antenna pre-amp which helps when storms roll into the area. It is about the same number of channels, I do like the ability to record a few minutes and after each show. The misses enjoys the ability to watch shows on her phone while she moving about the house in the morning. Overall Tablo TV is different from CM (I have gottne use to using Roku to get to Tablo) but it probably the best choice for the money of what is out there.

Thanks for taking the time to watch and write.

Thank you for taking the time to watch.

Sony and Eton had the same idea, although none of these radios are currently available in US. Temu and Alibaba might have other brands with NOAA and TV bands. The TV band could come in handy for areas in which the radio stations are automated and the only reliable weather info is on TV. Might be good just to have both a NOAA and a TV radios.

@@cfldriven Cool, I'll check Temu. Thanks, I appreciate the idea.

Linda, unless air got into it, you should be able just to stir it. I had my for over a year and it looked like jelly, but after stirring it was fine to paint with.

There was only about 1 5 inching bottom of jar. I used a drill attachment for mixing paint and it could barely turn. Maybe because jar was almost empty. I added 2 teaspoons,water and kink or messed up integrity of the paint. Still used it. Barely had enough to cover a dresser top I was using it for. I scrapped sides of jar and finally I got that satin smooth finish. Used a clear matt finish.

@@lindahoward8746 You are one determined person to use the last drop of this paint. Good for you. Thank you for sharing your story.

CS not sure why you think it not suitable for metallic surface mount as the receptacle has grounding points. Oops on the Shepard hook at 12 secs, even for a demo I should have caught it. Our home was built in 1968 with all copper wiring. We had a mix of back stab and hooked connections and some were done correctly and others not causing some of the issues you mentioned. Funny as this is a GE Gold Medallion home so you'd think the quality level would have been better. Thank you for watching and sharing.

Jozef, in the video the DC/DC outputs 125 amps, and 1812 watts. We limit the draw by using 100 amp fuse and an inverter that can only output 1000 watts. The system is purposely overbuilt for the little we ask of it. Remember purpose of this build was to run a frig, a natural gas tankless, and one or lights. Connecting to the traction battery would allow a higher amperage draw but it not a risk I am willing to take.

@@cfldriven As mentioned, the output load on the 12V DC/DC is calculated based on the car's needs. The idea that 125 amps are just sitting unused isn't accurate. The 12V system powers the brake pump, contactor circuits, lights, fans, and all the car's CPUs. If you think 125 amps is overbuilt, use an amp clamp meter on the engine cooling fan when the car is running hot to see its amp draw. Taking 100A with the inverter would leave only 25 amps for the car, which is barely sufficient. This would gradually strain your DC/DC converter and eventually cause it to fail.

@@uzefix Jоzef, this not a competition. In the video it is stated with car in READY to turn off other systems before using the DC/AC inverter. My HV DC current draw was under 5amps. Fan draws 2.0 amps at 14.7v and 1.7amps at 12.0v. Not sure what you mean by the car running hot, it just sitting in Park with minimal load. During the charging cycle it not getting hot enough to cause the fan to come on. The Prius is a very efficient system. Driving load is very different from just sitting with a connected DC/AC inverter. This solution may not be for everyone but it based on research and safety considerations.

The car HAS no needs if it's sitting stationary. Stop trolling. Go make a video if you think you're an expert . You won't, because you're a childish troll @@uzefix

@@cfldriven a 300w inverter would be absolutely fine, 1 kw if you use it all of that for a long time, that's a potential problem. The traction battery is a great way to convert an old G2 Prius, out of warranty anyways, into a long term generator with a UPS system, and thus get 2.5kw of power. Gas engine will run a lot of course at that draw, but a great way to power a home in Florida after a hurricane, or for an oil/gas furnace in Vermont after a bad winter storm killed power. This isn't me supporting a troll, which I don't think he is, just another way to do it. I prefer a 2 battery setup with a 1kw inverter, with a physical separation between both batteries that can be controlled, use the hybrid system to recharge at a lower amp rate the 2nd battery when needed.

Janae, thank you for watching and taking the time to share about your successful project. Good luck on the kitchen cabinets, it is real important to remove all the grease build up. They recommend Simple Green, full strength, Spic and Span, Fantastic, or Mr. Clean.

Steve, that is as far as it would go, until this past winter when I was able to pull it out further to the pivot joint.

It is for almost any surface you want to paint. I have not tested for oil resistance.

Glad you found this video and that it saved you some money. Congrats on getting the project done.

Gary, I would recommend checking www.partselect.com which has diagrams of the machine that might help you with disassembly. Thank you for watching.

And thank you for watching.

If the float moves freely it could be the micro switch. I would call their customer support.

Oleg, good question. Consulting with electrical wire charts we sized for cable that could carry in excess of 125 amps with the least amount of electrical resistance. Thank you for watching.

I agree, but what is available can be tinted. Thanks for watching.

MrBrian, thank you for sharing another solution.

Per your request I have answered your question here ua-cam.com/video/fQjG8R0S5jE/v-deo.html Enjoy!

Mike, yes there is a fan that comes on when using the induction cook top. In a quiet kitchen it is noticeable.

@@cfldriven does the fan run the entire time

@@Dtownvino I seldom notice the fan is running so I paid attention to it last night. The fan comes on when an induction coil is selected. It will remain on until after the cook top cools off.

Pam, I would recommend removing the screens as you'll probably need to manually follow up when using this product.

On these old system you are limited to 16Gb max. Here are some numbers for some others in the same family. Latitude E6430 DDR3 16 GB Latitude E6430 ATG DDR3 16 GB Latitude E6530 DDR3 16 GB Latitude E5530 DDR3 SDRAM 8 GB

John, sorry to disappoint, but we did demonstrate how anyone using Consumer Reports' calibration numbers could make image improvements to their TV. Coming soon is a video on using a the smartphone calibration mode. Thank you for watching.

@cfldriven thank u. Where i live best buy stopped doing tv calibrations and no business does it here. Very few individuals here are into tvs

@@johnlerma9753 When I worked in Post Production we would calibrate our monitors, but even a professionally set up monitor may not be pleasing to the viewer. Some prefer mis-calibrated because they want a warmer, brighter or more vivid display. For those calibration gets you to a known start point from where you can dial to taste.

@@cfldriven thank u. So much for everything

Thank you for taking the time to watch and provide feedback.

Garth, thank you for that great reminder. In our case the Rheem tankless draws less than 2 amps which is well within the limits of the CyberPower. One should always compare the amp and wattage draw of all devices to make sure they don't exceed what the power supply can safely handle.

@@cfldriven thought it might have been a joke. Hard to believe that under a load of so much immediate heat/energy (enough for a hot shower) only 2 amps is drawn. Double digit power draw, amps, while under load is not uncommon with most tankless water heaters. Some over larger systems can peak in the triple digits. You must have an efficient unit. Or possibly 2 amps is only while at idle?? Be safe.

@@garthzader I should clarify our Rheem tankless runs on natural gas so the power draw is just for the blower and electronics. Now the electric version of the same unit has a huge power draw as you have noted.

@@cfldriven ahh, that sounds right. Thanks for the clarification!